| Article number: | 840724069453 |
| Availability: | In stock (4) |
Soft White. 15ml (formly rubber base)
The NSI Builder Gel is a brand new hybrid gel that can be used for easy building of the nail, or for a slight apex for some added durability.
With the Builder Gel you can sculpt a full set of nails in just half the time of a traditional gel enhancement - and then soak to remove them in the same amount of time. No pots or jars, just one bottle and full control.
Designed for an extra strong gel polish application and use over natural nails. Perfect for short tip extensions and short sculpted extensions.
Once you finish applying Builder Gel, you have the perfect base or your nail art creations. Paint it with Polish Pro for a polished look or use 3D embellishments to wow a client. Build a gel nail enhancement with the ease of applying gel polish, the strength of a hard gel, and the versatility of acrylics.
Made by NSI's own facillity in the USA.
This product is vegan.
Instructions
1. Spray your and your clients’ hands with Purify and gently massage.
Push back the cuticle and gently remove shine with an Endurance
180/180 Grit file. Using a Nail Wipe saturated with Nailpure Plus,
press and rub into the natural nail.
2. If extensions are desired, adhere the tip or fit form at this time.
3. Apply Essential Bond to the natural nail. Allow to dry for one minute. They
will not appear chalky white.
4. Before you begin sculpting your enhancement, apply an even layer of
Essential Base Coat, this thin layer will ensure that proper bonding and
adhesion will occur for the subsequent layers. Cure in Dual Cure Lamp,
LED for 30 seconds or UV for 2 minutes.
NATURAL NAIL OVERLAY
1. Open your Builder Gel (choice of colour) and brush down the gel
onto the nail plate as if it were a gel polish. Place the gel near the
cuticle line, allowing room for your margin, and pull product forward
towards the free edge. Be sure to cover the body of the nail with a
thin even coverage of the gel. Cure in the Dual Cure Lamp, LED for
60 seconds or UV for 2 minutes.
2. Do not remove the tacky dispersion layer. Apply a second thin coat
of Builder Gel (choice of colour). Be sure to cover the body of the
enhancement with a thin even coverage of the gel. Cure in the Dual
Cure Lamp, LED for 60 seconds or UV for 2 minutes.
3. Check the nail from all angles to ensure proper apex placement. If
necessary, apply a small amount of Builder Gel(choice of colour) to
the upper arch. Cure in the Dual Cure Lamp, LED for 60 seconds or
UV for 2 minutes. Use a Nail Wipe saturated with Cleanse to remove
the tacky dispersion layer.
4. Refine file using your Endurance 180/180 Grit File. Check for proper
design and apex placement. File the nail so it is smooth, balanced and
attractive following the curvature of the nail. Remove excess dust with
your Plush Brush. Use a Nail Wipe saturated with Cleanse to remove
any dust that may be hiding in the side walls.
5. Apply Glaze ‘n Go LED or Essential Seal and cure in the Dual Cure
Lamp. LED for 30 seconds or UV for 2 minutes. Wipe off the tacky
dispersion layer using a Nail Wipe saturated with Cleanse. Condition
the cuticle and surrounding skin with Nurture Oil.
SCULPT (TIP OR FORM)
1. Open your Builder Gel (choice of colour) and brush down the gel
onto the nail plate as if it were a gel polish. Place the gel near the
cuticle line, allowing room for your margin, and pull product forward
towards the free edge. Be sure to cover the body of the nail with a
thin even coverage of the gel. Cure in the Dual Cure Lamp, LED for
60 seconds or UV for 2 minutes.
2. Do not remove the tacky dispersion layer. Apply a second thin coat
of Builder Gel (choice of colour). Be sure to cover the body of the
enhancement with a thin even coverage of the gel. Cure in the Dual
Cure Lamp, LED for 60 seconds or UV for 2 minutes.
3. Check the nail from all angles to ensure proper apex placement. To
reinforce the structure of the enhancement, you will need to apply
a small amount of Builder Gel (choice of colour) to the upper
arch. Cure in the Dual Cure Lamp, LED for 60 seconds or UV for 2
minutes. Use a Nail Wipe saturated with Cleanse to remove the tacky
dispersion layer.
4. Refine file using your Endurance 180/180 Grit File. Check for proper
design and apex placement. File the nail so it is smooth, balanced
and attractive following the curvature of the nail. Remove excess dust
with your Plush Brush. Use a Nail Wipe saturated with Cleanse to
remove any dust that may be hiding in the side walls.
5. Apply Glaze ‘n Go LED or Essential Seal and cure in the Dual Cure
Lamp. LED for 30 seconds or UV for 2 minutes. Wipe off the tacky
dispersion layer using a Nail Wipe saturated with Cleanse. Condition
the cuticle and surrounding skin with Nurture Oil.
Add colour of your choice
REMOVAL
1. Remove the the shiny shield of Essential Seal with an Endurance
180/180 Grit File.
2. Place the tips of the fingers into a bowl of Soothing Soak Off Remover.
This will keep your clients’ hands hydrated and pampered during
removal.
3. Continue to file and soak until product is completely removed. The
product will go frilly around the edges of the enhancement. When
ready it will be soft. Use and orange stick or equivalent tool to peel off
the remaining product.
OR
An excellent way to remove to Builder Gel System is to saturate a Nail
Wipe with Soothing Soak Off Remover and place on the nail. Then, wrap
the finger in aluminum foil and allow body heat to activate the removal.
